Identificador: 2590
Abierta
ID de articulo : # 2590 se ha agregado a su lista de deseos.
.PNG)
.PNG)
.PNG)
.PNG)
.PNG)
Descripción
TORNO 16'' X 40'' PARTE: 2GM-GML-1640HD
- ISO 9001 certified
- Large spindle bore 2-1/16”
- Heavy Duty spindle D1-6
- One-piece solid cast iron machine base
- Heavy Duty guideway width 10-1/4”
- Heavy Duty main motor 6 HP
- 16 spindle speeds from 45-1,800 rpm, speeds: 45/70/90/108/140/165/215/255/330/385/510/585/770/900/1170/1800rpm
- 45 kinds of inch threads, and 39 kinds of metric threads
- Threading and feeding rate change without changing gears
- Spindle is balanced, hardened and precision ground
- Spindle is supported at 3-point by high precision bearings
- All gears and shafts are hardened and precision ground
- Guideways induction hardened and precision ground
- Automatic lubrication system in headstock and feed box
- SINO DRO (installed)
- Taper turning attachment (installed)
- 8” 3-jaw chuck with one set of reversible jaws
- 10” 4-jaw chuck
- 12” Face plate
- 5 1/2” large steady rest with roller jaws (bearings)
- Oil pump on Apron for all guideways and leadscrews
- 2” follow rest with roller jaws (bearings)
- Removeable gap
- 4-way tools post
- Foot brake
- Halogen Work light and coolant system
- Full length splash guard
- (2) dead centers and (1) reducing sleeve MT6/MT4
- Thread chasing dial
- Tool box and leveling pads
Max. swing over bed | 16-1/16" |
Max. length of workpiece | 40" |
Max. swing over cross slide | 10-1/4" |
Max. Swing in gap | 23-1/4" |
Width of Bed | 10-1/4" |
Effective length in gap to spindle | 8-1/2" |
Effective length in gap to chuck jaws | 3-1/2" |
Spindle bore | 2-1/16" D1-6 |
Taper of spindle center | M.T. #6 (MT6/MT4 sleeve) |
Spindle speeds | 45-1,800 rpm / 16 steps |
Longitudinal feeds | 0.0018-0.07 IPR, 42 kinds |
Cross feeds | 0.0009-0.03 IPR, 42 kinds |
Inch threads | 70-2 TPI, 45 kinds |
Metric threads | 0.2-14 mm , 39 kinds |
Diametral Pitch threads | 8-40 DP , 21 kinds |
Module threads | 0.3-3.6 mm, 18 kinds |
Max. travel of top slide | 4-1/4" |
Max. travel of cross slide | 8-1/2" |
Spindle length w/o chuck Leadscrew length X TPI | 20-1/2" 1-1/4" x 4 TPI |
Diameter of tailstock quill | 2-1/16" |
Max. travel of tailstock quill | 5" |
Taper of tailstock quill center | MT4 |
Main motor:
Note: | 6 HP, 3 Phase, 20AMP Prewired: 220VAC
30AMP Breaker Needed ( 20A x 1.5 ) |
Coolant pump: | 1/8 HP, 220V, 3 Phase |
Oil for Headstock / Gear box / Apron | #30 weight machine oil Eg: Texaco regal R&O 100, 3 Gal. |
Net weight: | 4,150 lbs. |
Overall Dimensions (LxWxH): Shipping Dimensions: | 79" x 38" x 56" 80”x36”x70” |
Pago y Devoluciones
- Forma de pago
- N/A
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery1
REBAJADORA DE CAJONES
PARTE: 2CK-JEN60Designed to both notch and drill drawer boxes to install undermount soft-close drawer slides. The operation of the machine is simple with a self-indexing drilling unit that’s determined by the position of the drawer for either left or right notching. With a cycle time of approximately 10 seconds per drawer, you can achieve a high throughput and save time for other important tasks.High production capacity of up to 220 drawers machined per hour.57mm (2 ¼”) wide cutter head...
AMXmachinery1
ASTILLADORA - 15 PULGADAS
PARTE: 2TA-WG-1510 - ASTILLADORA - 15 PULGADASFeatures:A specially designed, powerful crusher for different materials such as wood, plastic, rubber, corn cob, etc.Excellent wearing ability and impact-resistant for time & labor saving.Large busting capacity and easy feeding system.The shaft rest for the cutter head is constructed by round hollow with special angle to keep cooling for long hours' usage.Cutter head angle cutting design allows aggressive cutting rates & high speed shredding of ...
AMXmachinery1
DOBLADORA DE METAL 4' X 3/16''
DOBLADORA DE METAL 4' X 3/16'' PARTE: 2GM-04316EThis machine has a 3HP Motor, rated at 220V three phase. Power bending roll up/down with push button & display.SO 9001 certifiedTaiwan machinesAll (3) rolls are hardened rolls, up to 50-52 HRC3-rollers are driven to perform high accuracyAdjustable cone attachment included3/8”, ½” and 5/8” grooves on rollersOne wheel one-side operated for bending rollOne wheel one-site operated for pinch roll (E model is power...
AMXmachinery1
SIERRA MULTIPLE DE VAIVEN
PARTE: 2TA-TRS-150F - SIERRA MULTIPLE DE VAIVENFEATURESMinimum kerf multi blade frame saw designed to maximize production and minimize material loss.Thin frame saw design accepts different saw frames & blade combinations.Unique design allows multiple saw fence configurations to produce single, double or multiple cuts in a single pass.Machine supplied with PLC controller to allow operator to maximize saw production & minimize down time.Production times are reduced because of the machine's du...