Identificador: 2458
Abierta
Descripción
PARTE: 12572 - PRENSA DE RADIO FRECUENCIA - OGDEN
USADA - BUENAS CONDICIONES
Curing area: 36” x 60” x 2” thick.
Clamping pressure is applied by multi-power (dual pistons on a common shaft) pneumatic cylinders to maximize pressure while relying on standard plant pressures. Unlike presses without multi-power cylinders, which require booster compressors, the Model SL36x60 reaches full capacity at 100-psi plant air pressure.
Edge pressure is applied by eight (8) each pusher shoes, each with a 4” bore x 4” stroke twin-piston multi-power pneumatic cylinders.
Top platen pressure is applied by two (2) 5” diameter x 16” stroke pneumatic cylinders through a cantilever arm that keeps the footprint to a minimum while still allowing the operator full access to the platen area.
The platen is set at a 45-degree angle and the top platen opens wide; allowing the operator to step inside the press for ergonomic and accurate parts placement.
The internal solid state RfsProtech 6KW Generator cures approximately 600 square inches of glue line per minute.
The Generator features solid state rectifiers and all aluminum cabinet for maximum conductivity and superior performance.
Two-hand no-tie-down safety controls for closing the top platen.
Controls are simple to understand, and are complete with the required push-buttons, switch, meters, digital operator display, and on-screen troubleshooting diagnostics.
The machine is controlled by a PLC for dependability and efficient maintenance. All controls will be provided for safe and efficient operation. The operator screen permits efficient operation, and the included press diagnostics screens assist in trouble-shooting when the need arises.
Proper interfaces will be provided for operational signals and emergency system stop.
All necessary RF controls, including buttons, meters, and PLC operator interface panel are mounted on a control panel attached to the left front of the press.
Interlocked top platen and safety switches on all access doors insure operator safety.
Power requirements are 480 volt, 60 cycle, 3 phase electric.
Circuit breaker protection is provided. A service disconnect is required for safety, but is not provided.
Powered In-Feed table with motor and controls
Out-feed steel deck
Voltage 480 volts 60 Hz
Pago y Devoluciones
- Forma de pago
- Transferencia/Deposito Bancario
Publicar mensaje
Ingresar to ask the seller a question.
AMXmachinery
CNC DRILL GLUE INSERT DOWEL MACHINE OMAL VELOX 1300
PART: 12062E – CNC DRILL – GLUE – INSERT – DOWEL MACHINE - OMAL VELOX 1300USED – IN VERY GOOD CONDITIONSIN MINT SHAPEMFG 2014 BUT WAS SOLD NEW JAN 2016YEAR 2014INCLUDES LASER PART SENSOR2 ZONE MACHINE WITH 51" WORKING AREAA LASER SENSOR AUTOMATICALLY MEASURES THE WIDTH OF A PANEL AND CALCULATED THE POSITION AND NUMBER OF DOWELS BASED ON A PROGRAM FILETESTED VIDEO 1:https://vimeo.com/438240935
AMXmachinery
ASTILLADORA – 30 HP – ABERTURA 60” X 60” APROX – SUDDRETH
PARTE: 12100 – ASTILLADORA – 30 HP – ABERTURA 60” X 60” APROX – SUDDRETHEn buenas condiciones30 HP Baldor rotor motor30" long rotor30" x 32" ram opening60'' x 60'' approx. hopper opening5 HP hydraulic ram motor1/2" screen openings, (needs repair)Weighs approx. 5,000 lbs
AMXmachinery
COMPRESOR PISTON 10 HP
PARTE # SIL-DC-10H500 – COMPRESOR DE PISTON HORIZONTAL – MOTOR 10 HP – 500 LTSNUEVO CON GARANTIACompresor de 10 HP Horizontal Tanque: 500 Litros Cabezal Marca FIAC Con guarda bandas Base en fierro colado, Cabezal en Aluminio y Cilindro en fierro colado DESPLAZAMIENTO: 40 CFM, 32 ACFM EFICIENCIA VOLUMETRICA 80% PRESIÓN MÁXIMA: 175 PSIG, 12 BAR Tiempo de llenado 4' 14" 1280 RPM Nivel sonoro 80 MOTOR 10HP, 7.5 KW, 120V, 3PH, 60HZ Conexión de desca...
AMXmachinery
DADO PARA LA CORTADORA DE ESQUINAS PARTE # ACC-CM40A - 3/8" RADIUS
PARTE: 2ACC-CM40A-DA – DADO PARA LA CORTADORA DE ESQUINAS PARTE # ACC-CM40A - 3/8" RADIUSNUEVO CON GARANTIA SOBRE DEFECTOS DE FABRICACION3/8" RADIUS1 en existencia en bodega en Chihuahua, Chih.Se usan tambien para cortar lamina para reconocimientos en las esquinas con redondos, etc. Capacidad de Corte:·Aluminio…................................................. .040"·Laton dureza media ................................ .025"·Plastico flexible......................................... .125...
3,900.00 MXN